• The Sunline forged OEM Brake lever is a great way to upgrade or replace your motorcycle brake lever with a strong and durable lever.
  • Sunline uses forged alloy construction to make the OEM brake levers more resistant to breaking.
  • Sunline forged OEM Brake levers are designed to fit in the stock perches.
  • For maximum strength and durability Sunline built the forged OEM brake levers to exceed OEM specifications.
  • The Sunline Forged OEM Brake lever comes with an adjustable stop which allows the brake lever to be adjusted to your hand size for maximum comfort and performance while riding.

SUNLINE FORGED OEM BRAKE LEVER

Price Range: $17.00 - $20.00
To purchase this part, please select a ride:
Select from rides that fit this product
Overall:
5 out of 5
5 out of 5
Location: salina ks
brake lever
" i put these on all of my bikes for 2 reasons... they dont break, and they are extremely lite. i will always buy these for replacements.... ALWAYS!!! "
Overall:
1 out of 5
1 out of 5
Location: Watkinsville, Ga
Worst Clutch cable i ever bought.
" I just purchased this for my 1997 KX125. I installed it and went to try it out and it snapped in half... from me just compressing it. Your better off getting an ASV lever. "
Overall:
5 out of 5
5 out of 5
Location: Not Available
GREAT!
" great brake. works good and doesn't brake off like my stock one. very good bang for the buck. "
Overall:
5 out of 5
5 out of 5
Location: Ivor,VA
Good Lever
" Have'nt broken a Sunline yet. Have 3 of these in toolbox that have been in hard crashes and all are bent, not broken. So im a tight wad and straighten them back out. I do have to replace after a few straightnings. Great lever for the money and do buy again. "
Overall:
1 out of 5
1 out of 5
Location: Not Available
Don't go cheap
" got the product everything was nice.it fit right and rode well it took two little spills and held up nice but fifth gear pinned out and slamming down to the ground it snapped right at the bolt. "
Overall:
5 out of 5
5 out of 5
Location: Bainbridge, Ga,
Sunline brake levers
" Good product, sturdy, hold up well even in the most furious crashes. "
Overall:
4 out of 5
4 out of 5
Location: Jacksonville, NC
Sunline Brake lever
" Great product at a great price. Son is in the "learning curve" of a YZ85 so the levers see more dirt than normal - OEM levers snapped off. This was a perfect fit and much more durable than stockers. "
Overall:
4 out of 5
4 out of 5
Location: pennsylvania
brake lever
" why pay more for a lever than you need to? serious riders, sure, pay the extra dough and get the high end levers. but, for those who like to muck and grind the trails, who smash levers, who pound their bikes, these are the levers for us! low cost for a good product. "
Overall:
5 out of 5
5 out of 5
Location: Crab Orchard, WV
Great replacement lever
" People this is a great lever, I got one for my YZ 250, that was broken before I bought the bike and it work out just fine, can't even tell it from oem !!! "
Overall:
1 out of 5
1 out of 5
Location: Not Available
clutch
" it is very very heavy and hard to pull in wen i start my bike i usely stall because its to heavy "
Overall:
5 out of 5
5 out of 5
Location: Bedford, PA
Nearly bendproof....very durable
" used this product on my 05 WR250F for approx. a week when my brother flipped the bike......it bent the handlebars pretty bad but almost unnoticeably bent this lever......a similar incident occurred with the stock lever and snapped it off......high regards to this lever.... "
Overall:
5 out of 5
5 out of 5
Location: Lawton, OK
a perfect fit
" The part was an exact replica of the orginal part, and easy to install, it had my son on the track in no time. "
Overall:
5 out of 5
5 out of 5
Location: wells river vt
good and rugide
" THis part is good and lasts. You can't ride with out them. "
Does the hardware come with it?
Asked by Kawa07
No, the use of the original stock/oem hardware must be reused.
Answered by james718, Portland, OR
HOW RESISTANT TO BREAKAGE ARE THESE LEVERS. ie FORGED VS CAST VS BILLET
Asked by bufford, bufford
A typical OEM lever is a casted aluminum lever. Casting will never be as strong as forging. But Billet will always be the strongest. This lever will be stronger than most OEM levers.
Answered by james718, Portland, OR
i always get the forged ones and i havent broken one yet. cast levers always break, and i have never used a billet lever. i would just stick with the forged levers if i were you.
Answered by burnzy, salina ks
Stubby
Asked by yz450fky
this lever is standard length.
Answered by james718, USA
it will be standard length. atleast mine was... if its not, send it back and order an OEM one.
Answered by burnzy, salina ks

Dirt Bike

Kawasaki

Kawasaki KDX220
Kawasaki KLX125L
Kawasaki KLX400R
Kawasaki KX100
Kawasaki KX125
Kawasaki KX250
Kawasaki KX250F
Kawasaki KX450F
Kawasaki KX500
Kawasaki KX60
Kawasaki KX65
Kawasaki KX80
Kawasaki KX85
KTM

KTM 125EXC
KTM 125SX
KTM 200EXC
KTM 250EXC
KTM 250MXC
KTM 250SX
KTM 250XC
KTM 400EXC
KTM 400MXC

KTM 450EXC
KTM 450MXC
KTM 450SX
KTM 450SXF
KTM 450XC
KTM 520EXC
KTM 520MXC
KTM 520SX
KTM 525EXC
KTM 525MXC
KTM 525SX
KTM 525XC
KTM 625SXC
KTM 65SX
Suzuki

Suzuki DR125
Suzuki DR250
Suzuki DR350
Suzuki DRZ125L
Suzuki DRZ250
Suzuki DRZ400E

Suzuki RM125
Suzuki RM250
Suzuki RM60
Suzuki RM65
Suzuki RM80
Suzuki RM85
Suzuki RMX250
Suzuki RMZ250
Suzuki RMZ450
Yamaha

Yamaha WR250
Yamaha WR250F
Yamaha WR426F
Yamaha WR450F
Yamaha YZ125
Yamaha YZ250
Yamaha YZ250F
Yamaha YZ426F
Yamaha YZ450F
Yamaha YZ80
Yamaha YZ85

MotoSport.com - The Guys That Ride!